Looking for a reliable 2200 PSI concrete pump for demanding industrial applications? The Blastcrete MX-10 Mixer/Pump is a high-pressure mixing and pumping solution designed for dense refractory shotcrete and pump-cast installations. Combining a powerful hydraulic pan mixer with a 3-inch ultra-high-pressure swing tube piston pump, the MX-10 is engineered to handle challenging refractory material placement requirements.
Since 1996, the MX-10 has been an established choice for monolithic refractory installations. Its 2,200 PSI piston face pressure, high-torque mixing system, and durable design make it suitable for demanding industrial projects where consistent material preparation and reliable pumping performance are essential.
The MX-10 is designed to deliver up to 10 tons of material per hour and is commonly used to pump suitable refractory materials over vertical distances exceeding 300 feet, depending on material properties and job-site conditions.
Request a Quote or Download the Brochure to learn more about the Blastcrete MX-10 and its capabilities.
What Makes the MX-10 a Powerful 2200 PSI Concrete Pump?
The Blastcrete MX-10 combines mixing and pumping in one integrated machine. Its 3-inch × 24-inch ultra-high-pressure swing tube piston pump is designed for refractory shotcrete and pump-cast applications that require high pumping pressure.
The hydraulic pan mixer prepares compatible materials before they enter the pumping system. This integrated design helps contractors manage material preparation and delivery for industrial refractory installation projects.
For businesses searching for a 2200 PSI concrete pump, the MX-10 offers a specialized solution for dense refractory materials, monolithic linings, and demanding industrial placement work.
Key Features of the Blastcrete MX-10
1. 2,200 PSI High-Pressure Pumping System
The MX-10 features a 3-inch × 24-inch ultra-high-pressure swing tube piston pump with a specified piston face pressure of 2,200 PSI.
This pumping system is designed to support demanding refractory pump-cast and shotcrete applications. The high-pressure configuration helps move compatible materials through a properly designed pumping line.
2. High-Torque Hydraulic Pan Mixer
The machine includes a hydraulic pan mixer with a capacity of 2,200 pounds and a stated mixing time of approximately 1.5 to 2 minutes.
This mixing system helps prepare refractory materials for pumping and placement. Following the material manufacturer's recommended mixing procedures is essential for achieving the required consistency and performance.
3. High Material Output
The Blastcrete MX-10 is designed to deliver up to 10 tons of material per hour. Its listed volumetric output range is 0–12 cubic yards per hour.
Actual output depends on material density, mix design, pipeline configuration, and operating conditions. Contractors should evaluate the required production rate and material specifications before selecting equipment.
4. Extended Vertical Pumping Capability
The MX-10 is commonly used to pump suitable refractory materials over vertical distances exceeding 300 feet.
This capability can benefit industrial projects where materials must be delivered to elevated installation areas or difficult-to-access locations. Actual performance depends on the material, elevation, pipeline layout, and other operating conditions.
5. Swing-Out Receiving Hopper
The MX-10 features a 2,500-pound-capacity swing-out receiving hopper equipped with a hydraulic agitator.
The swing-out design provides convenient access to the lower hopper and swing tube section for cleaning and maintenance. Forklift tubing on the lower hopper also supports flat-pack removal and handling.
6. Reliable Controls and Water Measurement
The machine includes solid-state electronics, solid-state valve control, a Fill-Rite water meter, and a 20-gauge dousing bucket for rapid water introduction.
These features support machine operation and material preparation. Water quantities should follow the refractory material manufacturer's specified mix design.
Applications of a 2200 PSI Concrete Pump
The Blastcrete MX-10 is designed primarily for industrial refractory applications involving compatible dense materials.
Refractory Shotcrete
Refractory shotcrete is used to apply specialized heat-resistant materials to industrial surfaces. The MX-10 combines high-pressure pumping with integrated mixing to support suitable shotcrete installation procedures.
Refractory Pump Casting
Pump-cast applications require refractory materials to be mixed and transported to the placement area. The MX-10 is designed to support these operations using its hydraulic pan mixer and swing tube piston pump.
Furnace and Kiln Linings
Industrial furnaces and kilns often require refractory linings to withstand high temperatures and demanding operating environments. The MX-10 can support compatible monolithic refractory installation work.
Boilers and Industrial Processing Facilities
Industrial boilers and processing facilities may require refractory installation, repair, or replacement. The MX-10 offers an integrated mixing and pumping system for suitable materials used in these applications.
Technical Specifications of the Blastcrete MX-10
Specification Details
Equipment MX-10 Mixer/Pump
Pump type 3" × 24" ultra-high-pressure swing tube
Pump pressure 2,200 PSI
Mixer type Hydraulic high-torque pan mixer
Mixer capacity 2,200 lbs
Mixing time 1.5–2 minutes
Output 0–12 cubic yards per hour
Stated material delivery capacity Up to 10 tons per hour
Discharge
2200 PSI Concrete Pump Blastcrete MX-10 Mixer/Pump for Industrial Applications
